Advantages of raymond milling machine
Raymond mill introduction
Raymond milling machine adopts electric control and realizes electric automatization management, for this reason, the quality of the electric parts such as disconnector of the electric motor will influences the normal operation and maintenance of the whole set of equipment. For this reason, when choosing electric parts for Raymond grinder, the customers should consider the quality of the products as well as the company strength and product stability.
Raymond mill is widely used in mining, cement, chemical grinding equipment, is an important non-metallic mineral processing equipment. Because Raymond stable performance, adaptability, cost-effective, since the introduction of China 20 years ago, has been applied to non-metallic mineral processing popularity.
Advantages of Raymond Mill
1. With three-dimensional structure, small floor space, and complete set of equipment, Raymond mill is an independent system from oversized materials to finished powder.
2. The fineness of finished products is uniform. The sieving rate reaches 99 %, which is difficult for other mill equipment.
3. The gearing of Raymond mill adopts sealed gear box and band pulley, which transmits smoothly and operates reliably.
4. The important parts are made of high quality steel. Wear parts are made of high wear-resistant materials. The overall machine has strong wear resistance and operates reliably.
5. The electric system of Raymond mill adopts centralized control. Unmanned operation of workshop becomes a reality.
Raymond formal operating procedures
1 , Before starting raymond mill, to check that all access doors are shut tight , if the body has iron , hard debris , adjust fan and host Raymond steering to see if reversing , Raymond local exhaust valve should be in the fully open position , you want to check screws, nuts are loose . Host belt is not too tight or too loose.
2 , starting jaw crusher ;
3 , to be there after the material hopper , start the analysis machines ;
4, start the blower ( air load starts to be functioning before loading ) ;
5 , start the host , the host at the start instant starts electromagnetic feeder . At this point the grinding work is started .
Raymond downtime when each machine should be turned off in the following order :
1, first turn off the feeder stop feeding ;
2 , about a minute after stopping the host ;
3 , blowing powder will stop after net residual blower ;
4 , finally close analysis machine. Shutdown sequence can be referred to as : Feeders - Host - Blowers - analysis machine .
Note: The delivery of materials to the silo elevator after a certain amount , the first stop and then stop the crusher upgrade , this should be the reservoir feeding amount changes
Application of raymond mill
Raymond mill widely used in barite, calcite, feldspar, silicon carbide, silicon carbide, talc, marble, limestone, dolomite, fluorspar, titanium dioxide, lime, activated clay, activated carbon, bentonite, kaolin, cement, phosphate ore, iron oxide, gypsum, glass, calcium carbonate, coal dry stone, coal, carbon black, clay, insulation materials, etc. Mohs hardness of not greater than 9.3 and humidity below 6% of non-flammable minerals, chemicals, construction and other industries more than 280 kinds of material for high fine powder generation and processing, R-pressure Raymond finished size 80-325 mesh of arbitrary regulation, part of the material up to 600 mesh.
What factors affect the efficiency of raymond mill?
As one of the important non-metallic deep processing equipment , Raymond mill is widely used in mining, cement plants and other production bases. Meanwhile Raymond mill does not live up to the unique performance characteristics and superior technology , we continue to meet the various needs of the market . In the production process, Raymond mill , there are a number of reasons from all sides will lead to a significant reduction in their productivity , what are the factors of it, to introduce the following :
1. the hardness of the product . In general , the nature of the material , the harder it harder Raymond mill , along with the difficulty of the material hardness mill upgrade will increase , and the more easy to wear Raymond mill .
2. The product of humidity. Raymond mill products containing large water too cold , in general, the moisture content of the product will cause adhesion inside large Raymond mill will process the next conveyor bet plug, greatly reduces the ability of Raymond mill .
3. The composition of the product . If you need the product contains more powder , it should advance once sieve to avoid a fine powder adheres inside the Raymond mill , the impact of transport .
4. The viscosity of the product . Since the viscosity of the product greater the adhesion force is large , it will affect the efficiency of Raymond mill .
5. Raymond Mill Raymond mill parts using the abrasion resistance and the better the performance , the ability of Raymond mill will be bigger, better able to mill products.
Raymond mill 's production efficiency is not static, you need the actual production and daily operations, pay attention to the details of the work , and better maintenance, more than just raise a few points Raymond mill production, the actual there is more production of small details that need attention. Skilled operation and precautions to use all aspects of the master Raymond mill can greatly improve production efficiency.
Raymond mill debugging
1, empty load test machine running at no load test machine before grinding roller device should hold the roll firmly with rope nets to avoid contact with the impact of the roller and grinding ring , and then empty the host machine running the test of not less than one hour ; Host should operate smoothly , cabinets oil should not exceed 80 ℃, temperature does not exceed 40 ℃. Analysis of the host machine and the direction of rotation shown in Figure 4 .
2 , the blower should load the boot , to be operating normally after the load , and then observe its smooth operation , no abnormal noise and vibration , bearing the maximum temperature should not exceed 70 ℃, the temperature rise should not exceed 35 ℃.
3 , the load test machine running time of less than 8 hours after the machine is working properly Raymond no abnormal noise , the pipe joints leak wind phenomenon , the test machine again after each fastener tightening , can be put into normal use.
Raymond milling machine adopts electric control and realizes electric automatization management, for this reason, the quality of the electric parts such as disconnector of the electric motor will influences the normal operation and maintenance of the whole set of equipment. For this reason, when choosing electric parts for Raymond grinder, the customers should consider the quality of the products as well as the company strength and product stability.
Raymond mill is widely used in mining, cement, chemical grinding equipment, is an important non-metallic mineral processing equipment. Because Raymond stable performance, adaptability, cost-effective, since the introduction of China 20 years ago, has been applied to non-metallic mineral processing popularity.
Advantages of Raymond Mill
1. With three-dimensional structure, small floor space, and complete set of equipment, Raymond mill is an independent system from oversized materials to finished powder.
2. The fineness of finished products is uniform. The sieving rate reaches 99 %, which is difficult for other mill equipment.
3. The gearing of Raymond mill adopts sealed gear box and band pulley, which transmits smoothly and operates reliably.
4. The important parts are made of high quality steel. Wear parts are made of high wear-resistant materials. The overall machine has strong wear resistance and operates reliably.
5. The electric system of Raymond mill adopts centralized control. Unmanned operation of workshop becomes a reality.
Raymond formal operating procedures
1 , Before starting raymond mill, to check that all access doors are shut tight , if the body has iron , hard debris , adjust fan and host Raymond steering to see if reversing , Raymond local exhaust valve should be in the fully open position , you want to check screws, nuts are loose . Host belt is not too tight or too loose.
2 , starting jaw crusher ;
3 , to be there after the material hopper , start the analysis machines ;
4, start the blower ( air load starts to be functioning before loading ) ;
5 , start the host , the host at the start instant starts electromagnetic feeder . At this point the grinding work is started .
Raymond downtime when each machine should be turned off in the following order :
1, first turn off the feeder stop feeding ;
2 , about a minute after stopping the host ;
3 , blowing powder will stop after net residual blower ;
4 , finally close analysis machine. Shutdown sequence can be referred to as : Feeders - Host - Blowers - analysis machine .
Note: The delivery of materials to the silo elevator after a certain amount , the first stop and then stop the crusher upgrade , this should be the reservoir feeding amount changes
Application of raymond mill
Raymond mill widely used in barite, calcite, feldspar, silicon carbide, silicon carbide, talc, marble, limestone, dolomite, fluorspar, titanium dioxide, lime, activated clay, activated carbon, bentonite, kaolin, cement, phosphate ore, iron oxide, gypsum, glass, calcium carbonate, coal dry stone, coal, carbon black, clay, insulation materials, etc. Mohs hardness of not greater than 9.3 and humidity below 6% of non-flammable minerals, chemicals, construction and other industries more than 280 kinds of material for high fine powder generation and processing, R-pressure Raymond finished size 80-325 mesh of arbitrary regulation, part of the material up to 600 mesh.
What factors affect the efficiency of raymond mill?
As one of the important non-metallic deep processing equipment , Raymond mill is widely used in mining, cement plants and other production bases. Meanwhile Raymond mill does not live up to the unique performance characteristics and superior technology , we continue to meet the various needs of the market . In the production process, Raymond mill , there are a number of reasons from all sides will lead to a significant reduction in their productivity , what are the factors of it, to introduce the following :
1. the hardness of the product . In general , the nature of the material , the harder it harder Raymond mill , along with the difficulty of the material hardness mill upgrade will increase , and the more easy to wear Raymond mill .
2. The product of humidity. Raymond mill products containing large water too cold , in general, the moisture content of the product will cause adhesion inside large Raymond mill will process the next conveyor bet plug, greatly reduces the ability of Raymond mill .
3. The composition of the product . If you need the product contains more powder , it should advance once sieve to avoid a fine powder adheres inside the Raymond mill , the impact of transport .
4. The viscosity of the product . Since the viscosity of the product greater the adhesion force is large , it will affect the efficiency of Raymond mill .
5. Raymond Mill Raymond mill parts using the abrasion resistance and the better the performance , the ability of Raymond mill will be bigger, better able to mill products.
Raymond mill 's production efficiency is not static, you need the actual production and daily operations, pay attention to the details of the work , and better maintenance, more than just raise a few points Raymond mill production, the actual there is more production of small details that need attention. Skilled operation and precautions to use all aspects of the master Raymond mill can greatly improve production efficiency.
Raymond mill debugging
1, empty load test machine running at no load test machine before grinding roller device should hold the roll firmly with rope nets to avoid contact with the impact of the roller and grinding ring , and then empty the host machine running the test of not less than one hour ; Host should operate smoothly , cabinets oil should not exceed 80 ℃, temperature does not exceed 40 ℃. Analysis of the host machine and the direction of rotation shown in Figure 4 .
2 , the blower should load the boot , to be operating normally after the load , and then observe its smooth operation , no abnormal noise and vibration , bearing the maximum temperature should not exceed 70 ℃, the temperature rise should not exceed 35 ℃.
3 , the load test machine running time of less than 8 hours after the machine is working properly Raymond no abnormal noise , the pipe joints leak wind phenomenon , the test machine again after each fastener tightening , can be put into normal use.